Connecticut CDL — Air Brakes Exam Simulation
25 questions · 20 correct to pass. You won't see any feedback until you finish — just like the real test.
Connecticut CDL — Air Brakes questions with answers
20 sample questions from the Connecticut CDL — Air Brakes question bank — each with the correct answer, a short explanation, and the section of the official handbook it comes from.
1. What is the main function of the air compressor?
Correct answer: It pumps air into the storage tanks
The compressor's job is to force air into the reservoirs so a supply of compressed air is always available; it is driven off the engine by gears or a belt.
Source: Connecticut CDL Manual, Section 5.1.1 (Air Compressor)
2. What does an antilock braking system do during hard braking?
Correct answer: It keeps the wheels from locking so you can steer and stay in control
ABS senses impending lockup and eases pressure to keep the wheels turning; it may not stop you sooner, but it lets you steer around obstacles and avoid skids.
Source: Connecticut CDL Manual, Section 5.4.2 (Braking with Antilock Brakes)
3. How does the air brake system warn drivers behind you that you are braking?
Correct answer: An air-operated electric switch turns on the brake lights
A stop light switch, an electric switch triggered by air pressure, lights the brake lamps when you apply the air brakes.
Source: Connecticut CDL Manual, Section 5.1.12 (Stop Light Switch)
4. How do you test that the parking brake will actually hold?
Correct answer: Set the parking brake, then ease the vehicle forward against it while in low gear
Stop the vehicle, apply the parking brake, and ease forward against it in low gear to confirm it holds.
Source: Connecticut CDL Manual, Section 5.3.3 (Final Air Brake Check)
5. In a dual air system at operating rpm, air pressure should climb from 85 to 100 psi in what amount of time?
Correct answer: Within 45 seconds
With the engine at operating speed, a dual air system should raise pressure from 85 to 100 psi in 45 seconds; larger-than-minimum tanks may take a bit longer.
Source: Connecticut CDL Manual, Section 5.3.3 (Final Air Brake Check)
6. The safety relief valve in the first air tank is usually set to open at what pressure?
Correct answer: 150 psi
That valve guards the system against excess pressure and typically opens at 150 psi; if it vents air, a problem exists and a mechanic should look at it.
Source: Connecticut CDL Manual, Section 5.1.6 (Safety Valve)
7. During the final air brake check, at about what pressures should the compressor cut in and cut out?
Correct answer: Cut in near 100 psi and cut out near 125 psi
When you test the governor, pumping should begin around 100 psi and stop around 125 psi; a governor that fails this may not keep enough air for safe driving.
Source: Connecticut CDL Manual, Section 5.3.3 (Final Air Brake Check)
8. The governor lets the compressor begin pumping again once tank pressure falls to what level?
Correct answer: Around 100 psi
The cut-in point sits near 100 psi; once the tanks drop to that pressure the governor allows the compressor to resume pumping.
Source: Connecticut CDL Manual, Section 5.1.2 (Air Compressor Governor)
9. If the low air pressure warning comes on while you are driving, what should you do?
Correct answer: Stop and safely park the vehicle as soon as possible
A low-air warning may mean a leak; controlled braking only works while air remains, so stop and park safely right away before the spring brakes engage on their own.
Source: Connecticut CDL Manual, Section 5.4.7 (Low Air Pressure)
10. A visible low air pressure warning must appear before tank pressure drops below what level?
Correct answer: 55 psi
On most vehicles the warning you can see has to activate before the tanks fall under 55 psi (older units use one half the governor cut-out).
Source: Connecticut CDL Manual, Section 5.1.11 (Low Air Pressure Warning)
11. With a manual transmission, when should you push in the clutch during a normal stop?
Correct answer: Not until the engine rpm has dropped close to idle
For a smooth, safe stop with a manual box, hold off on the clutch until engine rpm falls near idle, then pick a starting gear once stopped.
Source: Connecticut CDL Manual, Section 5.4.1 (Normal Stops)
12. For an average driver at 55 mph in good conditions, the total stopping distance of an air brake vehicle is about how far?
Correct answer: Over 450 feet
Adding perception, reaction, brake lag, and braking distance, the total at 55 mph comes to more than 450 feet for an average driver in good traction and brake conditions.
Source: Connecticut CDL Manual, Section 5.4.4 (Stopping Distance)
13. Which statement about the low air pressure warning signal is true for air brake vehicles?
Correct answer: Every vehicle with air brakes must have one
A low air pressure warning device is mandatory on any vehicle equipped with air brakes.
Source: Connecticut CDL Manual, Section 5.1.11 (Low Air Pressure Warning)
14. When checking a slack adjuster on an s-cam brake, how much movement suggests it needs adjustment?
Correct answer: More than roughly one inch of movement at the push-rod attachment point
With the parking brakes released and gloves on, pull hard on the slack adjuster; if it moves more than roughly one inch at the push-rod connection, it likely needs adjusting.
Source: Connecticut CDL Manual, Section 5.3.2 (Walk-around Inspection)
15. How do air brakes actually generate their stopping force?
Correct answer: They rely on compressed air to operate the brakes
Unlike the hydraulic brakes on cars, an air brake system uses compressed air to make the braking components work, which suits large, heavy vehicles.
Source: Connecticut CDL Manual, Section 5 (Air Brakes) - overview
16. When may you fully apply the brakes in an emergency stop?
Correct answer: When you routinely drive a straight truck or a combination that has working ABS on all its axles
The one exception to braking as usual is that a vehicle with functioning ABS on all axles can be brought to an emergency stop with the brakes fully applied.
Source: Connecticut CDL Manual, Section 5.4.2 (Braking with Antilock Brakes)
17. The application pressure gauge shows you need more and more pressure to maintain the same speed. What does that indicate?
Correct answer: The brakes are fading
Needing steadily more application pressure to hold a speed is a sign the brakes are fading; slow down and drop to a lower gear. Out-of-adjustment brakes, leaks, or mechanical faults can also cause it.
Source: Connecticut CDL Manual, Section 5.1.10 (Application Pressure Gauge)
18. Why should you avoid pressing the brake pedal while the spring brakes are already set?
Correct answer: The combined spring and air forces could damage the brakes
Pushing the pedal can load the brakes with the combined force of the springs plus the stored air pressure, which may damage them.
Source: Connecticut CDL Manual, Section 5.1.15 (Parking Brake Controls)
19. In a dual air brake system, what happens if one of the two systems becomes very low on pressure?
Correct answer: One end of the rig, front or rear, loses full braking power, so stops take longer
With one circuit very low, either the front or rear brakes lose full function, which lengthens your stopping distance; stop safely and get it repaired.
Source: Connecticut CDL Manual, Section 5.2 (Dual Air Brake)
20. Why is it important to drain the water that collects in the air tanks?
Correct answer: In cold weather the water can freeze and cause the brakes to fail
Compressed air carries moisture and a little oil that settle at the tank bottom; in freezing weather that water can turn to ice and knock out the brakes, so tanks must be drained fully.
Source: Connecticut CDL Manual, Section 5.1.4 (Air Tank Drains)